BUCKSTOP - BOSS "LED" BUMPER
BUCKSTOP - BOSS "LED" BUMPER
The Buckstop BOSS model bumper balances just the right amount of grill protection with a clean look and integrated mounting for a 30 inch curved LED lightbar. All aluminum construction planted on top of the bumper with a 5" x 6" footprint for serious protection.
ETA APPROX 6 WEEKS. GIVE US CALL TO CUSTOM ORDER YOURS WITH YOUR PREFERRED LIGHT ARRANGEMENT, COLORS, ETC.
2023/2024 OFFERINGS ARE ABOUT TO ROLL OUT. IF YOU HAVE A 23/24 F SERIES, REACH OUT AND WE CAN TALK THROUGH BUMPER OPTIONS.
- MATERIAL – Full strength. BUCKSTOP bumpers are 1/4″ steel in the primary impact zone and winch center and 3/16″ steel under the headlights. Very difficult to dent in animal strikes, very resilient in other collisions. As a comparison, 10 Gauge steel is roughly 1/8″ thick, 8 Gauge 5/32″.
- WEIGHT – Front Bumper and Grill Guard – approximately 190 lbs over stock.
- REMOVABLE GRILL GUARD – Serviceability. In cases where you need to service your radiator or grill, simply take of the grill guard – no need to un-wire the winch and lights and remove the entire bumper. Also, in the event of an extreme accident, the Grill Guard can be replaced without having to be cut off, re-welded, and re-painted.
- WINCH ACCESS DOOR – Keep your winch out of the weather. Top access door latches, protects the winch, and gives a clean look to the truck. When using the winch, remove the Access Door for an ample 2-foot opening to get at winch controls and cable spool.
- WINCH READY – Built-in mounting is provided for all standard 4½” x 10″ bolt pattern winches – face or floor mount. This covers almost all automotive winches. However, these winches will NOT work: Ramsey RE Series worm drive, Superwinch Husky Series worm drive, WARN 8274 upright, and all Megawinch.
- RUST PREVENTION – The best you can buy – sandblast and two-coat powder. BUCKSTOP bumpers are powder coated with an industrial strength, baked-on finish. Each bumper is fully sandblasted, coated with primer powder coat, baked and pre-cured, re-shot with topcoat, and baked and cured one more time. All critical seams are welded, inside and out. An open seam is a sure place for rust to develop.
- TOW HOOKS – Gotta have ’em. BUCKSTOP bumpers all have OEM “J” type tow hooks or re-located factory tow hooks. These hooks are easy to work with having plenty of clearance for attaching on a chain or tow strap and 180 degrees of pulling angle.
- TRAILER RECEIVER – You never know when… Standard on all BUCKSTOP winch bumpers. Used for carrier style winches, backing trailers into tight spots, negotiating that small boat down the ramp with your huge camper or van, attaching a flatbed trailer and using your winch to pull up the load, steps, push bars, tire carriers, the list goes on….
- LIGHTS – Pick your brand. BUCKSTOP bumpers have built-in universal light mounts that will accept any brand or style of big 6″ round lights. Lights are mounted inside the bumper behind stylish light buckets. Accessory light bar can be added to support up to four more big lights! Additional built-in light mounting is available as well as rectangular LED mounts.
- STYLING – No compromises. Careful attention has be given to the finer points of design that set your truck apart from the rest. Compact appearance, Grill Guard that follows the body lines, soft edges, superior finishing, and contours custom made for only your truck.
Integration of Driver Assist and Collision Warning Brake Support with Adaptive Cruise Control IS AVAILABLE. Buckstop is able to place the Radar Module into the bumper and maintain OEM functionality. The front camera will work best by omitting the Grill Guard altogether. However, the Classic I and II Grill Guards work well and block only a small amount of periferal view. The Outback and BOSS Grills are not recommended for Radar and Camera integration. CALL TO PLACE ORDER. ON-LINE ORDERING WILL NOT ACCOMODATE THE RADAR MODULE.